AS 350
|
1/4 Inch Drive Metric Torque Adapters
P/N TORQMET $110.00 This set of 1/4" drive torque adapters is like our SAE Torque adapters but in metric sizes. This set consists of 6, 8, 10 and 13 mm. This was requested by an EC mechanic that indicated these were the most common sizes. I have very little time on the metrics so you have to tell me what you need. Other sizes are available up to 14mm. Call or email with the size you need. The wrenches to the left are spline wrenches. Let us know what you need and we can customs make for you. |
|
|

Twist Grip Drive Tube and Control Pinion Attachment Work Aid
P/N ASB76A006
$165.00
Used to check correct bonding strength of the control pinion on the pilot and copilot collective lever driver tubes.
P/N ASB76A006
$165.00
Used to check correct bonding strength of the control pinion on the pilot and copilot collective lever driver tubes.

MO1 and MO5 MODULE OIL DRAIN HOSE
Drain hose for the MO1 and MO5 modules. Comes with a 7 foot hose.
P/N MO1/MO5
$75.00
Drain hose for the MO1 and MO5 modules. Comes with a 7 foot hose.
P/N MO1/MO5
$75.00

AS350 ENG AND OIL DRAIN
The AS350 eng oil and hyd oil tanks use the same drain.
This drain comes with a 7 ft hose just like all the rest.
P/N AS350ENGOIL
$75.00
The AS350 eng oil and hyd oil tanks use the same drain.
This drain comes with a 7 ft hose just like all the rest.
P/N AS350ENGOIL
$75.00

AS350 T/R G/BOX DRAIN
Not much to say here except that it comes with a 7 ft hose.
Stick it in the hole and the oil runs out.
P/N AS350DTG
$75.00
Not much to say here except that it comes with a 7 ft hose.
Stick it in the hole and the oil runs out.
P/N AS350DTG
$75.00

AS350 XSMN OIL DRAIN
Just like all the others except different.
P/N AS350DX
$75.00
Just like all the others except different.
P/N AS350DX
$75.00

AS350 St/Gen Seal Installer
Installs and seats the seal into the flange housing with air pressure.
I made this a while back for someone but never listed it until now. They said it works really well.
I finally got a chance to see it work so I now I'm listing it
for sale. If you know what this is I'm sure you know a lot more about it than I do.
P/N HWA8813824000
$895.00
Installs and seats the seal into the flange housing with air pressure.
I made this a while back for someone but never listed it until now. They said it works really well.
I finally got a chance to see it work so I now I'm listing it
for sale. If you know what this is I'm sure you know a lot more about it than I do.
P/N HWA8813824000
$895.00

AS350 SWASHPLATE SHIMMING AID
For those of you familiar with shimming the AS350 series swashplate you've probably
had to rent this before and know what it is.
The pic below is a breakdown of the individual pieces
P/N AS350SWSA
$1795.00
For those of you familiar with shimming the AS350 series swashplate you've probably
had to rent this before and know what it is.
The pic below is a breakdown of the individual pieces
P/N AS350SWSA
$1795.00

Torque Adapters 1/4" Drive
P/N TORQADAPT
$110.00 4pc SET (1/4, 5/16, 3/8, & 7/16)
$35.00 ea
Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter.
CONTACT US if you require a different size or length.
P/N TORQADAPT
$110.00 4pc SET (1/4, 5/16, 3/8, & 7/16)
$35.00 ea
Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter.
CONTACT US if you require a different size or length.

Brass Screwdriver for Compass Adjustment
P/N BRASSCA
$23.00
No more trying to make a screw driver for adjusting compasses with a hammer and welding rod.
This is a quality, solid brass screwdriver made especially for adjusting compasses.
It's 4 3/4 inches long and the blade tip is 5/32" wide.
P/N BRASSCA
$23.00
No more trying to make a screw driver for adjusting compasses with a hammer and welding rod.
This is a quality, solid brass screwdriver made especially for adjusting compasses.
It's 4 3/4 inches long and the blade tip is 5/32" wide.

Bolt Extractor
P/N XPRESS
$175.00
This work aid lets you apply pressure to the bolt while applying penetrating lube. Once the bolt pops loose it can easily be removed. Works great on the many control bolts and bell cranks found throughout the aircraft.
P/N XPRESS
$175.00
This work aid lets you apply pressure to the bolt while applying penetrating lube. Once the bolt pops loose it can easily be removed. Works great on the many control bolts and bell cranks found throughout the aircraft.