Helicopter Work Aids
  • Home
    • About Us
    • FAQ
    • Free Drains
  • Bell
    • Bell 206
    • Bell 407
    • Bell 429
    • Bell 505
    • Bell 212
    • Bell 222
    • Bell 412
    • Bell 427
  • Sikorsky
    • S-76
    • S-70 / UH-60
    • S-92
    • S-58
  • Other Airframes
    • BO 105
    • BO 117
    • AS 350
    • AW 109
    • AW 119
    • EC 120
    • EC 135
    • EC 145
    • MD500
    • Robinson
  • Powerplants
  • Contact
  • Non-Specific
    • Honda
    • Swing Wrenches

EC 135


Picture
Twist Grip Drive Tube and Control Pinion Attachment Work Aid
P/N ASB76A006
$185.00

Used to check correct bonding strength of the control pinion on  the pilot and copilot collective lever driver tubes.


Picture
EC135 Hydraulic Module Plunger Work Aid
P/N 135HMP
$185.00

Used to depress the plunger when bleeding the hydraulic system.


Picture
EC135 & EC145 Hydraulic Module Plunger Work Aid
P/N 145HMP
$235.00

This hydraulic module plunger work aid is designed for the aft facing hydraulic module on the 145 series aircraft. The older style plunger work aid is too large to fit between the transmission and hydraulic module. This work aid is required if you want to do the job right without damaging anything. It will work on both 145 and 135 hydraulic modules.


Picture
Pratt & Whitney PW200 Engine Sling
P/N PWESL
$190.00

Good on the PW200 series engines.


Picture
EC135 Engine Oil Drain
P/N EC135ENGOIL
$105.00

Comes with a 7 ft. hose.


Picture
EC135 Transmission Drain
P/N EC135DX
$105.00

Comes with a 7 ft. hose.


Picture
EC135 Tailrotor Gearbox Drain
P/N EC135DTG
$105.00

Comes with a 7 ft. hose.



Picture
1/4 Inch Drive Metric Torque Adapters 
P/N TORQMET
$110.00

This set of 1/4" drive torque adapters is like our SAE Torque adapters but in metric sizes.
This set consists of 6, 8, 10 and 13 mm. This was requested by an EC mechanic that indicated these were the most
common sizes. I have very little time on the metrics so you have to tell me what you need.
Other sizes are available up to 14mm. 
Call or email with the size you need. ​

We're not limited to just the sizes listed above.
Tell us what you want and we will put something together
.

Picture
 
Torque Adapter 12mm x 1/4" drive
P/N 12MMx1/4TA
P/N 13MMx1/4TA
​P/N 14MMx1/4TA

$35.00 ea

I have been getting requests for different sizes in 1/4" drive torque adapters.
We can make them in any size up to 9/16" in SAE or 14MM in metric.

If you don't see what you need contact us so we can discuss it with you.


Picture
Torque Adapters 1/4" Drive
P/N TORQADAPT
$110.00 4pc SET (1/4, 5/16, 3/8, & 7/16)
$35.00 ea

Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter. 

CONTACT US if you require a different size or length.


We're not limited to just the sizes listed above.
Tell us what you want and we will put something together
.


Picture
Brass Screwdriver for Compass Adjustment
P/N BRASSCA
$23.00

No more trying to make a screw driver for adjusting compasses with a hammer and welding rod.
This is a quality, solid brass screwdriver made especially for adjusting compasses.
It's 4 3/4 inches long and the blade tip is 5/32" wide.


Picture
Bolt Extractor
P/N XPRESS
$190.00

This work aid lets you apply pressure to the bolt while applying penetrating lube. Once the bolt pops loose it can easily be removed. Works great on the many control bolts and bell cranks found throughout the aircraft. 
​


Picture
Picture