1/4" Drive - 12 point Universal/Swivel Sockets SAE & METRIC MSRP: Was: Now: $60.00 - $85.00 Choose Options
Battery Adapter for Cordless Hydraulic Drive Unit (407PHMCordless) MSRP: Was: Now: $35.00 Add to Cart
Interchangeable Spanner Wrenches 6pc set 3/8 drive spanner wrenches. 6pc set Pin diameters: .090 .120 .190 MSRP: Was: Now: $105.00 Add to Cart
Field Maintenance Sheet Metal Field maintenance sheet metal kit for small jobs that any mechanic should be able to do anywhere. Contains: Rivet Squeeze with 1.5" and 3" Yoke 1ea Rivet Set: 2 flush sets and 3/32", 1/8", 5/32", & 3/16" universal head sets 1ea Blind Rivet... MSRP: Was: Now: $450.00 Add to Cart
Heavy Duty Mast Work Table Used to securely take apart and assemble mast assemblies. Due to the high torque on mast bearing nuts, the old way of clamping the mast into a vice may allow the mast to rotate and pivot on the vice which can become quite sketchy. This table makes it... MSRP: Was: Now: $0.00 Add to Cart
429 Main Rotor Torque Multiplier Fixture Main rotor assembly fixture for torquing the mast nut Bell P/N 429-210-001-101 MSRP: Was: Now: $5,500.00 Add to Cart
UV Flashlight for Transmission and Engine Oil Leak Checks UV flashlight for detecting oil leaks. Works great in the daytime (with cowlings on), works even better at night. Make sure you wash off your aircraft well before performing a ground run leak check with this light. It will light up ALL your residual oil... MSRP: Was: Now: $30.00 Add to Cart
1/4" Drive - 12 point Universal/Swivel Sockets SAE & METRIC We have located some quality swivel sockets at an affordable price that we are happy to offer here! They are made by Genius Tools. SAE (6pc) set consists of 1/4", 5/16", 3/8", 7/16", 1/2", & 9/16" Metric (9pc) set consists of 6mm, 7mm, 8mm, 9mm,... MSRP: Was: Now: $60.00 - $85.00 Choose Options
1/4" Drive Breaker Bar 1/4" drive breaker bar that is perfect for our special tools and replaces a ratchet that is always rotating. You should be fighting the helicopter, not your tools. Works great with the 407 Hydraulic Pump Wrenches. MSRP: Was: Now: $15.00 Add to Cart
Battery Adapter for Cordless Hydraulic Drive Unit (407PHMCordless) This is a battery adapter for our Makita hydraulic drive unit. This adapter allows you to use a Milwaukee or Dewalt. MSRP: Was: Now: $35.00 Add to Cart
429 Tail Rotor Balance Work Aid Work aid for balancing the tail rotor on the 429 If after three adjustments it is not possible to achieve successful dynamic balance of the tail rotor assembly, this workaid 111486325 can be installed to help the tail rotor balance process and to... MSRP: Was: Now: $250.00 Add to Cart
3/4" Drive Ratchet *EXCESS INVENTORY* 3/4" Drive Ratchet for a price you won't find anywhere else. These are extras from a kit we purchase and do not use the ratchet. So we are offering it reasonably priced. MSRP: Was: Now: $50.00 Add to Cart
429 Tail Rotor Driveshaft Hangar Bearing Accelerometer Mount Accelerometer mount for driveshaft hangar bearings. MSRP: Was: Now: $75.00 Add to Cart
Pin Gauges For Inspecting Splines All pin gauges are 2 inches long unless otherwise specified. Pin gauges can be modified for different lengths for an extra fee. If you do not see the diameter pin you need, let us know. We can have them here the very next day. We try to keep all... MSRP: Was: Now: $20.00 - $350.00 Choose Options
10X Magnifying Glass We chose this model of magnifying glass because the cup is setup for the correct focal distance. Just place the magnifying glass on the object you are trying to inspect and you are focused. No fighting the loupe trying to figure out the correct focus... MSRP: Was: Now: $20.00 Add to Cart
Ultimate Swing Wrench Kit Ultimate Swing Wrench Kits contains 28 pieces. They are: T-handle, Screwdriver handle, and curved handle Open End: 1/4, 5/16, 3/8, 7/16, 1/2, & 9/16 Ratcheting Open End: 5/16 Regular Box End: 1/4, 5/16, 3/8, 7/16, 1/2, & 9/16 Ratcheting Box End:... MSRP: Was: Now: $1,750.00 Add to Cart
429 Main Rotor Hub Cone Set 3 Jaw Puller This is a 3 jaw puller that the maintenance manual calls out for to remove the cone set from the main rotor hub. Our tool also comes with the stepper plate required (Its just not pictured). MSRP: Was: Now: $500.00 Add to Cart
Oil Can Dust Cap Instead of using a latex glove, we have all seen it, you can now save that half used can of oil with these caps specifically made for the quart cans. The Dust Cap protects your oil cans against dust, dirt and debris It saves money on leftover oil,... MSRP: Was: Now: $4.95 Add to Cart
206/407/429/505 Adapter Wrench 206L - Freewheeling Unit 407 - Freewheeling Unit 429 - Clutch Assembly 505 - Transmission Input Seal Bell P/N T103306 MSRP: Was: Now: $335.00 Add to Cart
Dykem Cross Check Torque Stripe We have this torque stripe in orange only MSRP: Was: Now: $10.00 Add to Cart
.020" Spherical Inspection Probe This is the spherical radius probe the maintenance manual calls for. This probe has a .020 spherical ball on the very end so that you can run it across the shaft splines to check for damage. Use it on: Multiple 206 items not listed... MSRP: Was: Now: $90.00 Add to Cart
206/407/429/505 Freewheeling Unit Bearing Installation Sleeve For pressing the roller bearing during freewheeling unit maintenance. For the "clutch" on the 429. Helitools 206-FWU-OH-16 Bell T103332 MSRP: Was: Now: $90.00 Add to Cart
Engine Wash Bottle SINGLE BOTTLE: This is a stainless, 2 1/2 gallon bottle that has been used by all the major operators in the Gulf of Mexico for the last 45 years to my knowledge. I have replaced the short stock hose with 7 ft of high quality chemical resistant... MSRP: Was: Now: $325.00 - $815.00 Choose Options
Reversible Swing Wrenches These reversible swing wrenches are an improvement over our other wrenches. We are using the reversible Gear wrench brand so when you get into a tight spot and can't get the wrench off the nut or bolt you can simply flip the reversing lever and back out... MSRP: Was: Now: $95.00 - $105.00 Choose Options
Brass Screwdriver For Compass Adjustment No more trying to make a screw driver for adjusting compasses with a hammer and welding rod.This is a quality, solid brass screwdriver made especially for adjusting compasses.It's 4 3/4 inches long and the blade tip is 5/32" wide. MSRP: Was: Now: $23.00 Add to Cart
Swing Wrenches Don't buy bulky swing wrenches from tool trucks made from the old ratcheting dog bone wrenches that were great 40 years ago. Ours are made with the slimmer profile Gearwrench ratcheting boxends. Rotor brakes, flight controls in the tailboom, or fuel... MSRP: Was: Now: $85.00 - $95.00 Choose Options
Grease Fitting - Straight These are the threaded ones, not the quick disconnect ones that get grease everywhere except the part you want it in. MSRP: Was: Now: $15.00 Add to Cart
Grease Fitting - 90° These are the threaded ones, not the quick disconnect ones that get grease everywhere except the part you want it in. MSRP: Was: Now: $20.00 Add to Cart
90° Grease Coupler I recently found this 90 degree grease coupler that works great on hard to access grease fittings.Works really well on the oil cooler blower bearings on the Bell 407. It slides in from the side when straight on access is difficult or next to impossible. MSRP: Was: Now: $16.00 Add to Cart
Torque Adapters 1/4" Drive Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter. SAE: The standard set consists of 1/4", 5/16", 3/8", &... MSRP: Was: Now: $50.00 - $170.00 Choose Options
Bell 429 & 505 Live Mount Gauge Pressure gauge in 2 psi increments (as per Bell Maintenance Manual) to calibrate live mounts on 429 and 505.Disclaimer: The manufacturer of the gauge will not warranty any gauge shipped out of the continental U.S. I can furnish a... MSRP: Was: Now: $575.00 Add to Cart
429 Main Rotor Head Stand Table top head stand for performing maintenance and overhaul procedures on the 429 main rotor head.Bolt to your table with 4 ea 5/8 bolts. MSRP: Was: Now: $1,200.00 Add to Cart
429 Main Rotor Head Puller We designed this puller after receiving reports that the 429 is having problems with head removal. Remove the mast nut and four hub through bolts. Place pressing plug on the mast. Install the puller plate with the aluminum spacers underneath it. Then... MSRP: Was: Now: $650.00 Add to Cart
429 Main Rotor Pitch Change Link Trammel Accurate, simple trammel for the 429 main rotor pitch change links. This trammel will outperform other universal trammels. MSRP: Was: Now: $480.00 Add to Cart
429 Idler Link Bushing R&R Remove and replace the ilder link bushings as per the maintenance manual. MSRP: Was: Now: $385.00 Add to Cart
429 Fan Shaft Assembly Work Aid - 4pcs set 429 Fan shaft assembly work aid per Bell specs. MSRP: Was: Now: $385.00 Add to Cart
429 PLA Alignment Guide Bell 429 PLA alignment aid Lines up the PLA base to the gearbox to prevent side loads on the PLA shaft. MSRP: Was: Now: $45.00 Add to Cart
429 Tail Rotor Gearbox Drain Tailrotor gearbox drain comes with a 7 ft hose. Probably don't need a 7 ft hose on a tailrotor gearbox drain, but that's what you get. You can shorten it to any length you want. MSRP: Was: Now: $95.00 Add to Cart
429 Engine Gearbox Drain Engine gearbox drain comes with a 7 ft hose. MSRP: Was: Now: $95.00 Add to Cart
429 Tail Rotor Mast Nut Socket Socket made as per Bell specifications. Requires removal of crosshead to perform torquing procedure. MSRP: Was: Now: $115.00 Add to Cart
429 Auxiliary Hydraulic Pump Drive Seal Work Aid This is another of the locally manufactured work aids that Bell has in their manuals. All you need is a local machine shop that works cheap or you can run to town and pickup a lathe and a couple hundred dollars of material to make what you need. Or give... MSRP: Was: Now: $105.00 Add to Cart
429 Tail Rotor Mast Nut Wrench Remove one of the allen screws and spread open the work aid. Close it back together and reinstall the screw. Torque the nut and then remove the screw and work aid. Almost as fast as reading this description. Does not require removal of crosshead. MSRP: Was: Now: $325.00 Add to Cart
429 Swashplate Shim Alignment Studs - 7pcs set Holds the shims in position when doing the swashplate friction check. The hex head is 5/32" drive. An allen wrench is easier to get in to tight areas than a long phillips screwdriver. Can also be used as jackscrews where a 1/4 28 jackscrew is needed. MSRP: Was: Now: $25.00 Add to Cart
Pratt & Whitney PW200 Engine Sling Good on the PW200 series engines. MSRP: Was: Now: $275.00 Add to Cart
Air Conditioner Belt Tensiometer Belt Tensiometer specified by Bell for checking air conditioning belt tension. Scale reads in pounds and kilograms Measures tension from 30 to 160 lb., and 15 to 75 kg. Die-cast aluminum body, nylon indicator arm and pressure pad Fits in pocket... MSRP: Was: Now: $30.00 Add to Cart
206L/407/429 CORDLESS Portable Hydraulic Pump Drive Unit Remove the hydraulic pump from the transmission with the hoses still connected and bolt hydraulic pump to the red pump pressure supply. The Cordless Makita is driven by a soft start, 5 speed, variable speed drive. You can finally lay to... MSRP: Was: Now: $4,900.00 Add to Cart
429 Main Rotor Blade Sling Main rotor blade sling aids in safely removing and installing main rotor blades. The 429 puts you at the upper limits of safely R&R the main rotor blades due to the hight of the blades, your work stands and short mechanics. Even a tall guy has to... MSRP: Was: Now: $2,100.00 Add to Cart
Oil Can Opener One Black Plastic "Church Key" FOD Free Turbine Oil Can Opener MSRP: Was: Now: $7.00 Add to Cart
429 PW207 Mag Seal Puller Slide Hammer used to remove Seal P/N 3058291-01 PWC64888 PWC64888-1 Designed with customer to fit tighter than PWC factory workaid. All 3 lips engage. MSRP: Was: Now: $525.00 Add to Cart
