206/505 Transmission & Tail Rotor Gearbox Input Pinion Remover MSRP: Was: Now: $550.00 - $1,450.00 Choose Options
206/407/505 Transmission Oil Pump Accessory Gear Drive Spanner Nut Socket MSRP: Was: Now: $290.00 Add to Cart
Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412) MSRP: Was: Now: $300.00 Add to Cart
206/407/505 Tail Rotor Gearbox Input/Output Bearing Retaining Nut Wrench MSRP: Was: Now: $425.00 Add to Cart
206/407/505 Freewheeling Unit Shaft Removal Work Aid - PLATE ONLY MSRP: Was: Now: $350.00 Add to Cart
206/407/505 Transmission Accessory Bevel Gear Bearing Work Aid Used to hold the accessory drive gear while applying torque to the gearshaft spanner nut MSRP: Was: Now: $450.00 Add to Cart
Spring Scale 0-50lbs 0-50 lbs Spring Scale. This spring scale is made of brass and will not shatter in your tool box like the cheap plastic spring scales. I've used both, brass and the plastic case spring scales. They both work. I just prefer the brass since they are a... MSRP: Was: Now: $110.00 Add to Cart
407 Freewheeling Assembly Seal Installation/Removal Tool This tool is used to both remove and install the seal from the freewheeling shaft nut. Bell P/N T103307 MSRP: Was: Now: $500.00 Add to Cart
206/505 Transmission & Tail Rotor Gearbox Input Pinion Remover 206/505 Transmission And Tail Rotor Gearbox Input Pinion Remover Bell P/N T101507 MSRP: Was: Now: $550.00 - $1,450.00 Choose Options
206/407/429/505 Adapter Wrench 206L - Freewheeling Unit 407 - Freewheeling Unit 429 - Clutch Assembly 505 - Transmission Input Seal MSRP: Was: Now: $335.00 Add to Cart
206 Tail Rotor Gearbox Filler Neck Work Aids Work aids for removal and replacement of filler neck of tail rotor gearbox. Installer is aluminum tool pictured. Remover is the slide hammer with adapter. MSRP: Was: Now: $75.00 - $300.00 Choose Options
206 Trim Tab Bender Used to bend the trim tabs during track & balance. MSRP: Was: Now: $1,500.00 Add to Cart
Thread Detector A collection of male and female threads in SAE and Metric. If you are not well versed in thread identification, this is the item you have been looking for. MSRP: Was: Now: $35.00 Add to Cart
Dykem Cross Check Torque Stripe We have this torque stripe in orange only MSRP: Was: Now: $10.00 Add to Cart
205/206/212/407/412/505 Transmission Planetary Install Pin This pin is used in removing or installing planetary pinions or the spur gear in the planetary assemblies. Helitools P/N 206-XMSN-OH-10 Bell P/N T101332 MSRP: Was: Now: $75.00 Add to Cart
205/206/212/407/412/505 Transmission Planetary Guide Shaft This work aid is used in aligning the pinion assembly inner race during removal and installation of the retaining shaft in lower planetary housing. Helitools P/N 206-XMSN-OH-11 Bell P/N T101574 MSRP: Was: Now: $400.00 Add to Cart
206/407/505 Transmission Accessory Gear Backlash Work Aid Used to check backlash between the transmission main input gear and the accessory drive gear. Helitools P/N 206-XMSN-OH-07 Bell P/N T101735 MSRP: Was: Now: $1,500.00 Add to Cart
206L/505 Transmission Holding Fixture And Spline Wrench Set Fixture to hold the 206 L-model and 505 transmission during repair and overhaul. Helitools P/N 206-XMSN-OH-08L Bell P/N T101883 MSRP: Was: Now: $2,800.00 Add to Cart
206/505 Main Rotor Trunnion Centering Work Aid - Old Style This is the original work aid called out in the maintenance manual to perform the centering of the main rotor trunnion. You will also need a set of V-Blocks to go along with it. You can find V-Blocks here. We suggest you... MSRP: Was: Now: $200.00 Add to Cart
212/412/205 Tail Rotor Driveshaft Coupling Work Aid 212-412 Repack Tool C-shaped part is 3D printed. Color mary vary from photo when printed. MSRP: Was: Now: $180.00 Add to Cart
206/505 Tail Rotor Gearbox Pinion Bearing Work Aid Used to install the bearings on the input pinion of the tail rotor gearbox. Input pinion definitely not included for this price. Helitools P/N 206-TRDS-F-02 MSRP: Was: Now: $60.00 Add to Cart
206/407/505 Tail Rotor Gearbox Backlash Spline Wrench This spline wrench is used to measure backlash on the tail rotor gearbox and also to clamp into a vice. Helitools P/N 206-TRGB-OH-03 Bell P/N T101511 MSRP: Was: Now: $695.00 Add to Cart
206 Mast Spline Overhaul Wear Pins These are the .080 and .160 wear pins the manual calls out for to do the checks on the mast splines during overhaul. This set comes with 2ea .080 and 2ea .160 pins. MSRP: Was: Now: $40.00 Add to Cart
206/505 Transmission Duplex Bearing Nut Wrench Used on the duplex bearing retainer nut. Helitools P/N 206-XMSN-OH-02 Bell P/N T101501 MSRP: Was: Now: $1,500.00 Add to Cart
206/505 Mast V-Block These are the 4inch V-Blocks the maintenance manual calls for to do mast inspections/overhauls. It is a 2 piece set. It also doubles as an amazing paperweight. (Tested and approved) Helitools P/N 206-MAST-F-04 MSRP: Was: Now: $250.00 Add to Cart
206/505 Mast Assembly Nut Wrench Wrench is used to remove and torque the nut on the mast assembly during overhaul. Helitools P/N 206-MAST-F-02 Bell P/N T102040 MSRP: Was: Now: $650.00 Add to Cart
206/505 Mast Holding Fixture (Alternate) Used to hold the mast assembly when torque is applied to the ball bearing retaining nut during removal and installation. Helitools P/N 206-MAST-F-01 Bell P/N T101499 CLICK HERE FOR 206-240-002-101 MSRP: Was: Now: $800.00 Add to Cart
206/505 Transmission Backlash Work Aid This item is used to check the backlash between the main input pinion gear and the input driven bevel gear. CR&O has all the details. The base plate is NOT included. Click here for the baseplate Helitools 206-XMSN-OH-05 Bell... MSRP: Was: Now: $900.00 Add to Cart
206/407/505 Freewheeling Unit Cap Restraint Fixture Fixture used to hold freewheeling unit cap on vice while doing maintenance Helitools P/N 206-FWU-OH-11 Bell P/N T103308 MSRP: Was: Now: $475.00 Add to Cart
206/407/429/505 Freewheeling Unit Bearing Installation Sleeve For pressing the roller bearing during freewheeling unit maintenance. For the "clutch" on the 429. Helitools 206-FWU-OH-16 Bell T103332 MSRP: Was: Now: $90.00 Add to Cart
206 Mainrotor Head Sling Sling has a clear vinyl coating on the 1/4" cables. Cables are 6 feet long.Hooks have safety latches. Cable comes with inspection tag, serialized and weight certification.Included is a Certificate of Compliance/Test​Cable is rated at 2200 lbs. Each leg... MSRP: Was: Now: $210.00 Add to Cart
206 Lifting Clevis Lifting clevis for the 206 series (and now the 505). 204-011-178-001 MSRP: Was: Now: $1,850.00 Add to Cart
206 Pitch Horn Spreader Use it to spread the pitch horn and remove the trunnion fittings as per Bell Maintenance Manual. MSRP: Was: Now: $135.00 Add to Cart
206/505 Blade Pin Press No longer will you need to waste time with a stuck pin. Once you decide the pin is stuck, place the pin press around the grip with the large hole around the top of the pin. (The tool is upside down in the pictures) Reinstall the bottom plate (the... MSRP: Was: Now: $725.00 Add to Cart
206/505 Bell Control Tube Trammel Accurate, simple trammel for the 206B, L and 505 main rotor pitch change links. This trammel will outperform other universal trammels. MSRP: Was: Now: $500.00 Add to Cart
206/505 Grip Lock Bolt - 2pcs Set Simplest, fastest, and best work aid to keep from scrapping a pair of TT Straps. Stronger and more reliable than T-handle type locks that most people use. MSRP: Was: Now: $40.00 Add to Cart
Bolt Extractor This work aid lets you apply pressure to the bolt while applying penetrating lube. Once the bolt pops loose it can easily be removed. Pressure is applied to the bolt and not to the tail boom fitting. Cracked fittings require tail boom removal at lots of... MSRP: Was: Now: $225.00 Add to Cart
206/505 Series Main Rotor Grip Locks - 2pcs set These lock tight, won't slip and are used to adjust the grips level when aligning and static balancing the main rotor. MSRP: Was: Now: $205.00 Add to Cart
206/407/505 Transmission Oil Pump Accessory Gear Drive Spanner Nut Socket Socket specifically designed for the spanner nut on the accessory gear that drives oil pump. Maintenance manual calls out for AN8515-1 Spanner Wrench. Our socket is a better design that won't slip and make you bust your knuckles. MSRP: Was: Now: $290.00 Add to Cart
Reversible Swing Wrenches These reversible swing wrenches are an improvement over our other wrenches. We are using the reversible Gear wrench brand so when you get into a tight spot and can't get the wrench off the nut or bolt you can simply flip the reversing lever and back out... MSRP: Was: Now: $95.00 - $105.00 Choose Options
Brass Screwdriver For Compass Adjustment No more trying to make a screw driver for adjusting compasses with a hammer and welding rod.This is a quality, solid brass screwdriver made especially for adjusting compasses.It's 4 3/4 inches long and the blade tip is 5/32" wide. MSRP: Was: Now: $23.00 Add to Cart
206/407/505 Oil Cooler Blower Driveshaft Spanner Wrench Wrench to get off the spanner nut on the oil cooler blower. The L-model wrench will also work on the 407. MSRP: Was: Now: $70.00 Add to Cart
206 Knurl Nut Wrench This will easily remove that stuck knurl nut. It is especially great if you want to replace the knurl nut liner and don't want to ruin the knurl nut with channel locks because the knurl nut is frozen. MSRP: Was: Now: $130.00 Add to Cart
Grease Fitting - Straight These are the threaded ones, not the quick disconnect ones that get grease everywhere except the part you want it in. MSRP: Was: Now: $15.00 Add to Cart
Grease Fitting - 90° These are the threaded ones, not the quick disconnect ones that get grease everywhere except the part you want it in. MSRP: Was: Now: $20.00 Add to Cart
90° Grease Coupler I recently found this 90 degree grease coupler that works great on hard to access grease fittings.Works really well on the oil cooler blower bearings on the Bell 407. It slides in from the side when straight on access is difficult or next to impossible. MSRP: Was: Now: $16.00 Add to Cart
Swashplate Shim Alignment Studs Holds the shims in position when doing the swashplate friction check. The hex head is 5/32" drive.An allen wrench is easier to get in to tight areas than a long phillips screwdriver. Can also be used as jack screws on the 206 and 407 transmission input... MSRP: Was: Now: $20.00 Add to Cart
206/505 Latch Bolt Nut Socket This socket is normally used in the shop for removal of the grip assembly. Bell P/N T101544 MSRP: Was: Now: $95.00 Add to Cart
206L Tach Generator Driveshaft Removal & Installation Work Aid Work aid to remove and replace tach generator driveshaft as seen in figure 63-7c MSRP: Was: Now: $125.00 Add to Cart
206 Main Rotor Hub Pitch Horn Lock Use this work aid when lifting the hub assembly from the mast. Remove upperside of pitch control links and install the work aid. MSRP: Was: Now: $425.00 Add to Cart
206 Main Rotor Hub Trunnion Fixture For installing the bearings on the trunnion without putting undue stress on the splines. MSRP: Was: Now: $190.00 Add to Cart
206 Tail Rotor Hub Trunnion Fixture Fills in the trunnion, so it is not crushed during pressing of wear sleeves. MSRP: Was: Now: $50.00 Add to Cart
206 Swashplate Uniball Fixture Supports lower portion of uniball when pressing in the lower bushings. MSRP: Was: Now: $75.00 Add to Cart
206 Swashplate Uniball Lower Bushing Remover Removes lower bushings from swashplate uniball. MSRP: Was: Now: $55.00 Add to Cart
Torque Adapters 1/4" Drive Hard to find 1/4" drive torque adapters. Most torque adapters you will find are 3/8" drive. These will allow you to use that low torque 1/4" torque wrench without the 3/8" to 1/4" adapter. SAE: The standard set consists of 1/4", 5/16", 3/8", &... MSRP: Was: Now: $35.00 - $110.00 Choose Options
Bell 429 & 505 Live Mount Gauge Pressure gauge in 2 psi increments (as per Bell Maintenance Manual) to calibrate live mounts on 429 and 505.Disclaimer: The manufacturer of the gauge will not warranty any gauge shipped out of the continental U.S.Most companies do... MSRP: Was: Now: $575.00 Add to Cart
Bell 505 Tail Boom Rigging Pin - 143 ​Required for rigging the tailboom on the 505. 427-201-001-143 MSRP: Was: Now: $85.00 Add to Cart
Bell 505 Tail Boom Rigging Pin - 147 ​Required for rigging the t/boom on the 505. 427-201-001-147 MSRP: Was: Now: $85.00 Add to Cart
505 Free Wheeling Unit Drain Hose The freewheeling unit chip plug on the 505 sits in a pan assembly that requires an extra short drain fitting because of clearance issues. The position also requires a suction pump to pull the oil out of the freewheeling unit assembly. It just won't... MSRP: Was: Now: $145.00 Add to Cart
Air Conditioner Belt Tensiometer Belt Tensiometer specified by Bell for checking air conditioning belt tension. Scale reads in pounds and kilograms Measures tension from 30 to 160 lb., and 15 to 75 kg. Die-cast aluminum body, nylon indicator arm and pressure pad Fits in pocket... MSRP: Was: Now: $30.00 Add to Cart
Oil Can Opener One Black Plastic "Church Key" FOD Free Turbine Oil Can Opener MSRP: Was: Now: $7.00 Add to Cart
ENGWASH-HF-BRACKET This is just the brackets and fasterners necessary to attach your (ENGWASHx2) double engine wash bottle set up to a Harbor Fright Welding Cart. Purchase your own Welding Cart from Harbor Freight and use these brackets to fasten them to the... MSRP: Was: Now: $150.00 Add to Cart
Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412) Swashplate Gimbal Ring Bolt Removal Workaid (204B, 205, 212 & 412) 204B-22-27 205-22-45 205B-22-29 212-22-74 412-22-93 MSRP: Was: Now: $300.00 Add to Cart
206/407/505 Tail Rotor Gearbox Input/Output Bearing Retaining Nut Wrench Used to apply torque to the input bearing retaining nut and the output bearing retaining nut. T101512 206-TRGB-F-04 MSRP: Was: Now: $425.00 Add to Cart
206/505 Transmission Bearing Installation and Removal Plug P/N 206XBS-HT Used to support the input driven spiral bevel gearshaft duplex bearing by the outer race while pressing bearing into or out of the transmission lower case. T101503 206-XMSN-OH-25 MSRP: Was: Now: $725.00 Add to Cart
206/505 Transmission Gear Shaft Nut Wrench Used to apply torque to the input driven spiral bevel gearshaft duplex bearing outer ring retaining nut. Bell P/N T101502 Helitools' P/N 206-XMSN-OH-03 MSRP: Was: Now: $225.00 Add to Cart
206/505 Mast Holding Fixture Used to hold the mast assembly when torque is applied to the ball bearing retaining nut during removal and installation. Bell P/N 206-240-002-101 Helitools P/N 206-MAST-F-05 CLICK HERE FOR T101499 MSRP: Was: Now: $850.00 Add to Cart
206/505 Trunnion Hex Screw Wrench Used to torque hex insert screw in trunnion/pillow block. 206-MR-OH-18 MSRP: Was: Now: $96.00 Add to Cart
206 & 505 Main Rotor Blade Alignment Pins - 2pcs Easier and faster than mirrors and cheaper than a laser.No calibration needed. Drop it in the bolt hole and set the string. 206-MR-F-06 MSRP: Was: Now: $115.00 - $145.00 Choose Options
206 Planetary Shaft Sleeve Used to remove aand install the planet gear shaft from and into the arm of the spider and the bearing assembly inner race. T101506 206-XMSN-OH-20 MSRP: Was: Now: $525.00 Add to Cart
206/505 Tailrotor Rigging Flap Lock Work Aid Bell designed flap lock for 206/505. These were acquired through purchase of HeliTools inventory. Limited supply. See our design here. MSRP: Was: Now: $25.00 Add to Cart
206/407/505 Freewheeling Unit Wrench Used to remove and install the 214-040-241 nut. This tool replaces wrench assembly 407-240-006-101. 206-FWU-OH-18 T101960 MSRP: Was: Now: $150.00 Add to Cart
206/505/407 Freewheeling Unit Duplex Bearing Removal Driver Used to remove the 406-040-531 bearing from the 406-040-508 Cap Assembly. 206-FWU-OH-15 T103324-101 MSRP: Was: Now: $250.00 Add to Cart
206/407/505 Freewheeling Unit Bearing Installation Sleeve Used to install the 206-040-206 bearing into the 406-040-516 shaft. 206-FWU-OH-17 T103333 MSRP: Was: Now: $90.00 Add to Cart
206/407/505 Freewheeling Unit Shaft Removal Work Aid - PLATE ONLY Used in conjuction with plug to remove shaft from the bearing. 206-FWU-OH-12 T103310-103 MSRP: Was: Now: $350.00 Add to Cart
206/407/505 Freewheeling Unit Shaft Removal Work Aid - PLUG ONLY Used in conjuction with plate to remove shaft from the bearing. 206-FWU-OH-12 T103310-105 MSRP: Was: Now: $150.00 Add to Cart
206/407/505 Freewheeling Unit Shaft Removal Work Aids Used in conjuction with a press to remove the shaft from the bearing. T103310-101
