407 Freewheeling Unit Assembly Aft Adapter Wear Sleeve Installation Tool MSRP: Was: Now: $150.00 Add to Cart
206/505 Transmission & Tail Rotor Gearbox Input Pinion Remover MSRP: Was: Now: $550.00 - $1,450.00 Choose Options
206/407/505 Transmission Oil Pump Accessory Gear Drive Spanner Nut Socket MSRP: Was: Now: $290.00 Add to Cart
10X Magnifying Glass We chose this model of magnifying glass because the cup is setup for the correct focal distance. Just place the magnifying glass on the object you are trying to inspect and you are focused. No fighting the loupe trying to figure out the correct focus... MSRP: Was: Now: $30.00 Add to Cart
Kaflex Drive Shaft Protective Maintenance Cover Place this pad on the kaflex shaft during maintenance or when removed to protect it from dings and scratches. There are 2 options: 206 and 407. The 206 is a bit longer than the 407. Kaflex definitely not included for this price. MSRP: Was: Now: $75.00 Choose Options
407 Tail Rotor Hub Flapping Bearing Work Aid Used to apply the force for installation and removal on steel outer race of flapping bearing. That wording is straight from the manual. Bell P/N T101750 MSRP: Was: Now: $775.00 Add to Cart
206/505 Mast Assembly Overhaul Kit Kit contains all special tools to complete 206 mast overhaul as per CR&O. MSRP: Was: Now: $2,260.00 Add to Cart
206/407/505 Swashplate Roll Stake Bearing Work Aid Bearing staking tool for the swashplate bearings. Allows you to perform the maintenance on the aircraft without removing the swashplate. MSRP: Was: Now: $2,000.00 Add to Cart
407 Tail Rotor Gearbox Output Shaft Work Aid #3 Used to hold the tail rotor output shaft during removal and torquing of bolts. MSRP: Was: Now: $450.00 Add to Cart
407 Tail Rotor Gearbox Output Shaft Work Aid #2 This work aid is used to help press the output shaft out of the gearbox housing and for other jobs involving an arbor press and the gearbox housing. MSRP: Was: Now: $750.00 Add to Cart
Ultimate Swing Wrench Kit Ultimate Swing Wrench Kits contains 28 pieces. They are: T-handle, Screwdriver handle, and curved handle Open End: 1/4, 5/16, 5/16 Ratcheting Open End, 3/8, 7/16, 1/2, & 9/16 Regular Box End: 1/4, 5/16, 3/8, 7/16, 1/2, & 9/16 Ratcheting Box End:... MSRP: Was: Now: $1,750.00 Add to Cart
407 Cyclic Rigging Pin Cyclic rigging pin that gets installed from below the aircraft into that fitting that is plugged up by 5 different paint schemes. You know exactly what I'm talking about. MSRP: Was: Now: $55.00 Add to Cart
429 Main Rotor Hub Cone Set 3 Jaw Puller This is a 3 jaw puller that the maintenance manual calls out for to remove the cone set from the main rotor hub. Our tool also comes with the stepper plate required (Its just not pictured). MSRP: Was: Now: $500.00 Add to Cart
407 Tail Rotor Gearbox Wear Sleeve Installation Tool Used to install the wear sleeve on the output shaft of the tail rotor gearbox. Bell P/N T103303 MSRP: Was: Now: $300.00 Add to Cart
206/407/505 Transmission Accessory Bevel Gear Bearing Work Aid Used to hold the accessory drive gear while applying torque to the gearshaft spanner nut. Bell P/N T101504 MSRP: Was: Now: $450.00 Add to Cart
Spring Scale 0-50lbs 0-50 lbs Spring Scale. This spring scale is made of brass and will not shatter in your tool box like the cheap plastic spring scales. I've used both, brass and the plastic case spring scales. They both work. I just prefer the brass since they are a... MSRP: Was: Now: $110.00 Add to Cart
407 Freewheeling Unit Assembly Aft Adapter Wear Sleeve Installation Tool Used to install the wear sleeve on the aft adapter of the freewheeling unit. Bell P/N T103311 MSRP: Was: Now: $150.00 Add to Cart
407 Tail Rotor Gearbox Input Duplex Bearing Nut Lip Seal Tool This tool is used to remove and install the lip seal on the duplex bearing nut on the input of the tail rotor gearbox. Bell P/N 427-240-155-101 For Carbon Seals click here MSRP: Was: Now: $750.00 Add to Cart
407 Tail Rotor Gearbox Output Shaft Pusher Used for the installation of the tail rotor gearbox output shaft Bell P/N T103320 MSRP: Was: Now: $120.00 Add to Cart
Rolls-Royce 250 Fuel Nozzle Holding Fixture Another one where the name of the tool describes it beautifully. Rolls-Royce P/N 6897875 MSRP: Was: Now: $690.00 Add to Cart
407 Tail Rotor Gearbox Input Duplex Bearing Nut Carbon Seal Tool This tool is used to remove and install the CARBON seal on the duplex bearing nut on the input of the tail rotor gearbox. Bell P/N T103219 MSRP: Was: Now: $375.00 Add to Cart
407 Freewheeling Assembly Seal Installation/Removal Tool This tool is used to both remove and install the seal from the freewheeling shaft nut. Bell P/N T103307 MSRP: Was: Now: $500.00 Add to Cart
407 Transmission Backlash Bar Assembly Used to check the backlash in plane of rotation between pinion and gear on the transmission assembly. Bell P/N T103326 MSRP: Was: Now: $475.00 Add to Cart
407 Transmission Mast Duplex Bearing Nut Wrench Tool to remove the mast duplex bearing nut from the bottom of the transmission Bell P/N 407-240-004-101 MSRP: Was: Now: $6,000.00 Add to Cart
407 Mast Assembly Overhaul Kit This kit contains the following items: Mast Assembly Holding Fixture 407-240-008-101 Mast Assembly Nut Wrench 407-240-007-101 Bearing removal plate T103318 Work Aid #1 & #2 Work Aid #3 Foam and case MSRP: Was: Now: $3,800.00 Add to Cart
407 Tail Rotor Driveshaft Work Aid Kit This kit contains the following items: Step Plate OTC 8068 Step Plate OTC 8062 Puller OTC 1025 And 4 pressing work aids MSRP: Was: Now: $571.00 Add to Cart
Rolls-Royce 250 Starter/Generator Seal Remover Special slide hammer tool used to remove the seal from the starter/generator. MSRP: Was: Now: $525.00 Add to Cart
Oil Can Dust Cap Instead of using a latex glove, we have all seen it, you can now save that half used can of oil with these caps specifically made for the quart cans. The Dust Cap protects your oil cans against dust, dirt and debris It saves money on leftover oil,... MSRP: Was: Now: $4.95 Add to Cart
206/505 Transmission & Tail Rotor Gearbox Input Pinion Remover 206/505 Transmission And Tail Rotor Gearbox Input Pinion Remover Bell P/N T101507 MSRP: Was: Now: $550.00 - $1,450.00 Choose Options
206 Hydraulic Servo Rigging Pins Rigging pins for the hydraulic servos. Bell P/N T102019 MSRP: Was: Now: $75.00 Add to Cart
407 Tail Rotor Gearbox And Swashplate Vise Mount This fixture is made to hold both the tail rotor gearbox and the swashplate in a vise. Bell P/N T103220 Tail Rotor Gearbox Work Aid #5 Swashplate Work Aid #1 MSRP: Was: Now: $475.00 Add to Cart
206 Greased Driveshaft Grease Applicator This is for the unfortunate souls that still have to pack grease into the older style greased driveshafts. If you have a Kaflex driveshaft, this won't work for you, but we will absolutely still sell it to you. You can make it into a cool key ring and... MSRP: Was: Now: $10.00 Add to Cart
206/407/429/505 Adapter Wrench 206L - Freewheeling Unit 407 - Freewheeling Unit 429 - Clutch Assembly 505 - Transmission Input Seal MSRP: Was: Now: $335.00 Add to Cart
206 Trim Tab Bender Used to bend the trim tabs during track & balance. MSRP: Was: Now: $1,500.00 Add to Cart
Thread Detector A collection of male and female threads in SAE and Metric. If you are not well versed in thread identification, this is the item you have been looking for. MSRP: Was: Now: $35.00 Add to Cart
206B Drag Pin Spherical Bearing Staking Tool Set These are used to remove the spherical bearing in the drag pin assembly on the 206B Bell P/N T101547 Helitools' P/N 206-XMSN-OH-22 MSRP: Was: Now: $999.00 Add to Cart
206 & 407 Tailboom Support Stand 206 & 407 Tailboom Support StandCall for more information.The tailboom can be removed or installed on the aircraft by one person with this stand.This stand is designed for high skid aircraft. If you have a low skid aircraft contact us so we can... MSRP: Was: Now: $0.00 Add to Cart
205/206/212/407/412/505 Transmission Planetary Guide Shaft This work aid is used in aligning the pinion assembly inner race during removal and installation of the retaining shaft in lower planetary housing. Helitools P/N 206-XMSN-OH-11 Bell P/N T101574 MSRP: Was: Now: $400.00 Add to Cart
206/407/505 Transmission Accessory Gear Backlash Work Aid Used to check backlash between the transmission main input gear and the accessory drive gear. Helitools P/N 206-XMSN-OH-07 Bell P/N T101735 MSRP: Was: Now: $1,500.00 Add to Cart
206L/505 Transmission Holding Fixture And Spline Wrench Set Fixture to hold the 206 L-model and 505 transmission during repair and overhaul. Helitools P/N 206-XMSN-OH-08L Bell P/N T101883 MSRP: Was: Now: $2,800.00 Add to Cart
206/505 Main Rotor Trunnion Centering Work Aid - Old Style This is the original work aid called out in the maintenance manual to perform the centering of the main rotor trunnion. You will also need a set of V-Blocks to go along with it. You can find V-Blocks here. We suggest you... MSRP: Was: Now: $200.00 Add to Cart
407 Freewheeling Unit Bolt Wrench This "wrench" is used to hold the freewheeling unit adapter bolt. I don't know why the aircraft part is called a bolt or why this tool is called a wrench, but here we are. Helitools P/N 407-FWU-OH-22 Bell P/N 406-240-012-101 MSRP: Was: Now: $750.00 Add to Cart
212/412/205 Tail Rotor Driveshaft Coupling Work Aid 212-412 Repack Tool C-shaped part is 3D printed. Color mary vary from photo when printed. MSRP: Was: Now: $180.00 Add to Cart
206/505 Tail Rotor Gearbox Pinion Bearing Work Aid Used to install the bearings on the input pinion of the tail rotor gearbox. Input pinion definitely not included for this price. Helitools P/N 206-TRDS-F-02 MSRP: Was: Now: $60.00 Add to Cart
RR250 C20/30/47 Engine Sled Made to fit the C20/C30/C47. Easy assembly and disassembly for shipping. Rolls-Royce P/N 6891189 MSRP: Was: Now: $900.00 Add to Cart
206/407/505 Tail Rotor Gearbox Backlash Spline Wrench This spline wrench is used to measure backlash on the tail rotor gearbox and also to clamp into a vice. Helitools P/N 206-TRGB-OH-03 Bell P/N T101511 MSRP: Was: Now: $695.00 Add to Cart
206 Mast Spline Overhaul Wear Pins These are the .080 and .160 wear pins the manual calls out for to do the checks on the mast splines during overhaul. This set comes with 2ea .080 and 2ea .160 pins. MSRP: Was: Now: $46.00 Add to Cart
206/407/429 Hydraulic Pump Shaft Spline .020 Wear Probe This is the spherical radius probe the maintenance manual calls for. This probe has a .020 spherical ball on the very end so that you can run it across the shaft splines to check for damage. MSRP: Was: Now: $90.00 Add to Cart
407 Freewheeling Unit Aft Cap Lip Seal Work Aid Used to install the lip seal on the freewheeling unit aft cap. 1.98in wide by .500 thick. Updated Manual says to make it .250 thick. We make it .500 because it is easier to manufacture and it also makes it easier for you to grip the work aid and... MSRP: Was: Now: $60.00 Add to Cart
206/505 Transmission Duplex Bearing Nut Wrench Used on the duplex bearing retainer nut. Helitools P/N 206-XMSN-OH-02 Bell P/N T101501 MSRP: Was: Now: $1,500.00 Add to Cart
206/505 Mast V-Block These are the 4inch V-Blocks the maintenance manual calls for to do mast inspections/overhauls. It is a 2 piece set. It also doubles as an amazing paperweight. (Tested and approved) Helitools P/N 206-MAST-F-04 MSRP: Was: Now: $250.00 Add to Cart
206/505 Mast Assembly Nut Wrench Wrench is used to remove and torque the nut on the mast assembly during overhaul. Helitools P/N 206-MAST-F-02 Bell P/N T102040 MSRP: Was: Now: $650.00 Add to Cart
206L Elevator Rigging Work Aid Requested by a mechanic, this T-bar is offset 6.5 degrees at the very end. You can use a fancy digital protactor to set the elevator angle, or you can get this easy to use, permanently set angle T-bar, that won't fluctuate readings on top of a helicopter... MSRP: Was: Now: $90.00 Add to Cart
407 Main Rotor Hub Assembly Adapter Adapter is used to maintain alignment of main rotor hub assemblies during teardown and re-assembly for overhaul. Bell 407-210-005-101 MSRP: Was: Now: $2,200.00 Add to Cart
407 Tail Rotor Driveshaft Hanger Bearing Disassembly Work Aid Provides support to hanger bearing housing while pushing out bearing with arbor press MSRP: Was: Now: $60.00 Add to Cart
212/412 Tail Rotor Trunnion Centering Tool Figure 64-14 Tail Rotor Trunnion Centering Tool MSRP: Was: Now: $550.00 Add to Cart
206/505 Mast Holding Fixture (Alternate) Used to hold the mast assembly when torque is applied to the ball bearing retaining nut during removal and installation. Helitools P/N 206-MAST-F-01 Bell P/N T101499 CLICK HERE FOR 206-240-002-101 MSRP: Was: Now: $800.00 Add to Cart
206/407 Airframe Fuel Filter Fixture Requested by a customer, this is a fixture to hold the Airframe Fuel Filter in a vice. Has 4 tabs on it, so you can put the filter in a position that makes it easier for you to work on. MSRP: Was: Now: $85.00 Add to Cart
206A/B Cyclic Bell-Crank Rigging Work Aid Work Aid to help rig the 3.09 inches from roof deck to the center of bolt on the cyclic bell-crank. MSRP: Was: Now: $35.00 Add to Cart
206B Transmission Holder/Fixture Fixture to hold the 206 B-model transmission during repair and overhaul Bell T101508 Helitools 206-XMSN-OH-14B MSRP: Was: Now: $1,600.00
206/505 Transmission Backlash Work Aid This item is used to check the backlash between the main input pinion gear and the input driven bevel gear. CR&O has all the details. The base plate is NOT included. Click here for the baseplate Helitools 206-XMSN-OH-05 Bell... MSRP: Was: Now: $900.00 Add to Cart
206L Tail Rotor Rigging Go/No-Go Gauge Use this Go/No-Go Gauge to set the 1.46" on the bellcrank at the bottom of the vertical tunnel (broom closet) during tail rotor rigging. Helitools 206-FC-F-07 MSRP: Was: Now: $45.00 Add to Cart
206/407/505 Freewheeling Unit Cap Restraint Fixture Fixture used to hold freewheeling unit cap on vice while doing maintenance Helitools P/N 206-FWU-OH-11 Bell P/N T103308 MSRP: Was: Now: $475.00 Add to Cart
206/407/429/505 Freewheeling Unit Bearing Installation Sleeve For pressing the roller bearing during freewheeling unit maintenance. For the "clutch" on the 429. Helitools 206-FWU-OH-16 Bell T103332 MSRP: Was: Now: $90.00 Add to Cart
205/212/412 Tail Rotor Yoke Support Work Aid Tail Rotor Yoke Support Work Aid as per the 205, 212, & 412 CR&O. This work aid is made from steel and weighs 35lbs (16kg). Helitools P/N 412-TR-OH-02 MSRP: Was: Now: $2,200.00 Add to Cart
RR250 Spur Adapter Gear Installation Work Aid P/N: 250SG2 (C20 only) Rolls-Royce P/N 23006778 P/N 250SG3 (C30 & C47) Rolls-Royce P/N 23005426 MSRP: Was: Now: $240.00 Choose Options
RR250 Accessory Drive Lip Seal Installs the Starter/Generator and HMU (Fuel Pump) seals on the C47 gearbox MSRP: Was: Now: $140.00 Add to Cart
Engine Wash Bottle SINGLE BOTTLE: This is a stainless, 2 1/2 gallon bottle that has been used by all the major operators in the Gulf of Mexico for the last 45 years to my knowledge. I have replaced the short stock hose with 7 ft of high quality chemical resistant... MSRP: Was: Now: $325.00 - $815.00 Choose Options
407 Kaflex Mounting Wrench If you have ever installed a Kaflex drive shaft, you know how its practically impossible to actually torque them. We designed these wrenches so you could stop using that calibrated elbow and properly torque them with a torque wrench. MSRP: Was: Now: $85.00 Add to Cart
206 Mainrotor Head Sling Sling has a clear vinyl coating on the 1/4" cables. Cables are 6 feet long.Hooks have safety latches. Cable comes with inspection tag, serialized and weight certification.Included is a Certificate of Compliance/TestCable is rated at 2200 lbs. Each leg... MSRP: Was: Now: $210.00 Add to Cart
206/407 Oil Cooler Blower Shaft Spline Wear Pins These are used to measure the wear on the oil cooler blower drive shaft splines. You get 2 each 0.108" pins and 2 ea 0.120 pins MSRP: Was: Now: $40.00 Add to Cart
206 Lifting Clevis Lifting clevis for the 206 series (and now the 505). 204-011-178-001 MSRP: Was: Now: $1,850.00 Add to Cart
206L/407/429 Portable Hydraulic Pump Drive Unit FOR CUSTOMERS OUTSIDE OF THE UNITED STATES PLEASE CLICK HERE Remove the hydraulic pump from the transmission with the hoses still connected and bolt hydraulic pump to the red pump drive unit. Plug in the Makita to 110v, and presto, you have... MSRP: Was: Now: $4,750.00 Add to Cart
Rolls-Royce 250 C47 Ratcheting Open-End Fuel-Control Swing Wrench Ratcheting open end swing wrench designed to remove that pesky upper 5/16 nut on the fuel control. With a slow and steady control of the swing wrench, I was able to remove the upper nut in approximately three minutes. Compare that to the last time you... MSRP: Was: Now: $85.00 Add to Cart
Bell 206 Transmission Cover and Lift Plate Cover plates for the 206 transmissions. Fitted with eye for lifting transmission. NOT for lifting aircraft.Lifting eye is rated for 9000 lbs MSRP: Was: Now: $290.00 Choose Options
Rolls-Royce 250 C20 Compressor Case Half Wrenches - 3pcs set With these wrenches, you can now cut down the time it takes to disassemble the case halves by 50%. Bits are removable which allows you to use the reverse side of the ratchet for removal and installation with just our two ratcheting wrenches. Comes with a... MSRP: Was: Now: $350.00 Add to Cart
Rolls-Royce 250 C20 Gearbox Seal Installer Installs the gearbox seals on the C20's. Place guide on output shaft, place seal over the guide, and place flange over the seal. MSRP: Was: Now: $300.00 Add to Cart
206 Pitch Horn Spreader Use it to spread the pitch horn and remove the trunnion fittings as per Bell Maintenance Manual. MSRP: Was: Now: $135.00 Add to Cart
Rolls-Royce 250 Turbine To Gearbox Attach Bolt Wrenches - 3pcs No longer will you need to use that calibrated elbow. We have designed 3 wrenches to perform the torque checks on the 6 turbine to gearbox attach bolts on the RR250-C30 and C47 engines. A long 1/4" extension will be required to torque the bolt above the... MSRP: Was: Now: $120.00 Add to Cart
Rolls-Royce 250 C30/C47 Fuel Nozzle Wrench This fuel nozzle wrench is double sided to give you better access to the fuel nozzle. With the cowling installed, if you place the wrench on the fuel nozzle, it may not sit the way you want because of the limited space, flip it to the other side. The... MSRP: Was: Now: $110.00 Add to Cart
Rolls-Royce 250 C30/C47 Medium Fuel Nozzle Wrench This wrench is usually preferred by the overhaul guys working the engine on a stand. MSRP: Was: Now: $95.00 Add to Cart
206/505 Blade Pin Press No longer will you need to waste time with a stuck pin. Once you decide the pin is stuck, place the pin press around the grip with the large hole around the top of the pin. (The tool is upside down in the pictures) Reinstall the bottom plate (the... MSRP: Was: Now: $725.00 Add to Cart
206/505 Bell Control Tube Trammel Accurate, simple trammel for the 206B, L and 505 main rotor pitch change links. This trammel will outperform other universal trammels. MSRP: Was: Now: $500.00 Add to Cart
206/505 Grip Lock Bolt - 2pcs Set Simplest, fastest, and best work aid to keep from scrapping a pair of TT Straps. Stronger and more reliable than T-handle type locks that most people use. MSRP: Was: Now: $40.00 Add to Cart
206B Bleed Valve Block Color varies when manufactured Bleed valve block for Rolls-Royce C20 engine with strap so that it can be hung. Rolls-Royce P/N 6886204 MSRP: Was: Now: $38.00 Add to Cart
Bolt Extractor This work aid lets you apply pressure to the bolt while applying penetrating lube. Once the bolt pops loose it can easily be removed. Pressure is applied to the bolt and not to the tail boom fitting. Cracked fittings require tail boom removal at lots of... MSRP: Was: Now: $225.00 Add to Cart
206 Mast Stand Adapter This adapter was made to fit inside of 2” galvanized pipe. Can be machined to fit in your stand. Please give us the size of the pipe you plan on using in the comments on checkout. If you need a mast stand for your 206L and don't have a scrap mast... MSRP: Was: Now: $230.00 Choose Options
206 Tail Rotor Rigging Work Aid Color varies when manufactured Made from PLA. Light and soft to protect tail rotor blades.Much lighter than the factory tool made from steel. Cheap enough you can purchase 2 pieces like Bell suggests in the maintenance manual to speed up the job. This... MSRP: Was: Now: $245.00 Choose Options
206/505 Series Main Rotor Grip Locks - 2pcs set These lock tight, won't slip and are used to adjust the grips level when aligning and static balancing the main rotor. MSRP: Was: Now: $205.00 Add to Cart
206/407/505 Transmission Oil Pump Accessory Gear Drive Spanner Nut Socket Socket specifically designed for the spanner nut on the accessory gear that drives oil pump. Maintenance manual calls out for AN8515-1 Spanner Wrench. Our socket is a better design that won't slip and make you bust your knuckles. MSRP: Was: Now: $290.00 Add to Cart
Rolls-Royce C30/C47 Engine Lifting Eye Engine lifting eye for C30 and C47. Long enough to clear the exhaust stack so it doesn't have to be removed. There are 3 3/8-24 threaded holes so the bolts can be stored when not in use. Rolls-Royce C20 6796963Rolls-Royce C30/C47... MSRP: Was: Now: $335.00 Add to Cart
OH58 Main Transmission Drain This is the main gearbox drain hose for the OH58. Pull your chip plug where you want to drain the transmission and check to see if it is the long or short style. Also check to see if the drain has 3 pins or 3 slots for engaging and locking into... MSRP: Was: Now: $95.00 Add to Cart
206B Transmission Drain 206B transmission drain comes with a 7 ft hose.This drain is used when the chip plug has the 3 pins to engage and lock. MSRP: Was: Now: $95.00 Add to Cart
206B&L Tail Rotor Gearbox Drain Tail Rotor Gearbox Drain for the 206 series aircraft. Comes with 7 ft hose. MSRP: Was: Now: $95.00 Add to Cart
206L Transmission Drain Main transmission drain for the 206L series aircraft. Bell P/N: DB3188L MSRP: Was: Now: $95.00 Add to Cart
206 Tail Rotor Mast Nut Socket 206 series tail rotor retaining nut extended socket. MSRP: Was: Now: $95.00 Add to Cart
206 Series Tail Rotor Crosshead Remover Used to remove the tailrotor crosshead on Bell 206 series aircraft.Safer and faster than the 2 jaw pullers. MSRP: Was: Now: $295.00 Add to Cart
Bypass Spool Check Mount - With Dial Indicator Bracket held on with nylon screws so as not to damage the servo anodized surface.The bracket also comes with a powder coat finish which gives additional protection to the anodized finish on the servo. Comes with spare nylon screw. If... MSRP: Was: Now: $80.00 - $255.00 Choose Options
Rolls-Royce 250 Ignitor Wrench Ignitors can be hard to remove for several reasons. Someone put it in too tight, didn't use anti-seize or used a 12 point socket and slipped, rounding off the corners. This wrench is made from a 6 point impact socket. Install the wrench and put the... MSRP: Was: Now: $65.00 Add to Cart
Rolls-Royce 250 Starter/Generator Spline Turn Wrench T-handle wrench for turning the N1 wheels while doing maintenance on the RR250 series engines. Starter/generator splines are hard to find, so get yours here Rolls-Royce P/N 6799790 MSRP: Was: Now: $55.00 Add to Cart
206 & 407 Free Wheeling Unit Aft Flange Wrench Use this work aid by attaching it to the aft flange with two bolts. Use a breaker bar to keep shaft from rotating. Through the larger centered hole, use your socket to torque the nut. We can make the square drive hole 1/2in if you prefer. Bell P/N... MSRP: Was: Now: $85.00 Add to Cart
Rolls-Royce C20 Engine Lifting Eye Engine lifting eye for C20 Long enough to clear the exhaust stack so it doesn't have to be removed. There are 3 3/8-24 threaded holes so the bolts can be stored when not in use. Rolls-Royce P/N C20 6796963 Rolls-Royce P/N C30/C47 6889888 MSRP: Was: Now: $335.00 Add to Cart