Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs MSRP: Was: Now: $145.00 Add to Cart
206/407/505 Tail Rotor Gearbox Input/Output Bearing Retaining Nut Wrench MSRP: Was: Now: $425.00 Add to Cart
206/407/505 Freewheeling Unit Shaft Removal Work Aids MSRP: Was: Now: $150.00 - $450.00 Choose Options
Rolls-Royce 250 Turbine Wheel Lock Used to lock the turbine wheel in place when installing the turbine section. The plate and rod are made from brass. The brass rod is soft enough to bend if necessary so it won't damage the turbine blades should excessive pressure be applied to the... MSRP: Was: Now: $65.00 Add to Cart
Rolls-Royce 250 St. Gobain PTO Seal Installer These are the seal installers for the new St Gobain seals p/n 23091293 (red) and p/n 23091353 (blue)They can also be used for installing the Viton SealsThe C20 and C30/47 have different seal insertion depths so order according to your engine model MSRP: Was: Now: $275.00 Choose Options
206 Main Rotor Trunnion Centering Fixture Specify which model aircraft (B or L) when ordering. This is the new and improved main rotor trunnion centering work aid. We have a memo with 5 pages of information on operation of the work aid that we can email to you. If you are on a budget or... MSRP: Was: Now: $250.00 - $975.00 Choose Options
206A/B/L Mast Assembly Work Aid #3 Work Aid #3 for the Mast Assembly found in the CR&O manual. Chapter 63-10 page 29. MSRP: Was: Now: $410.00 Add to Cart
429 Main Rotor Blade Sling Main rotor blade sling aids in safely removing and installing main rotor blades. The 429 puts you at the upper limits of safely R&R the main rotor blades due to the hight of the blades, your work stands and short mechanics. Even a tall guy has to... MSRP: Was: Now: $2,100.00 Add to Cart
205/212 Blade Bolt Socket Fits both the 205 and 212 blade bolt nut P/N 204-011-153-001 MSRP: Was: Now: $325.00 Add to Cart
RR250-C30/C47 Spur Adapter Gear O'ring Installation Work Aid For engines C30 and C47 only RR P/N 23006785 MSRP: Was: Now: $410.00 Add to Cart
407 Swashplate Shipping Plate Color varies when manufactured Protects swashplate and uniball from getting bounced around and beat up during shipping. MSRP: Was: Now: $55.00 Add to Cart
205/212/412 Transmission Input Quill Pusher Set Pusher Set - 3pcs To install transmission input quill Bell P/N T101586 MSRP: Was: Now: $450.00 Add to Cart
407 Hydraulic Pump Spline Wear Pins 407 Hydraulic pump splines wear pins .0200" (x2) & .0400" (x2) Click here for a selection of different size pins MSRP: Was: Now: $40.00 Add to Cart
Rolls-Royce 250 Starter/Generator Seal Installer & Fuel Pump Seal Installer - 2pcs This work aid is a 2 in 1. Use it on either the starter/generator seal or the fuel pump seal. Simplifies installation of seals and removes chances of damaging seal while installing. This work aid is only for lip seal (23079054). MSRP: Was: Now: $145.00 Add to Cart
206/407/505 Tail Rotor Gearbox Input/Output Bearing Retaining Nut Wrench Used to apply torque to the input bearing retaining nut and the output bearing retaining nut. T101512 206-TRGB-F-04 MSRP: Was: Now: $425.00 Add to Cart
206/505 Transmission Bearing Installation and Removal Plug P/N 206XBS-HT Used to support the input driven spiral bevel gearshaft duplex bearing by the outer race while pressing bearing into or out of the transmission lower case. T101503 206-XMSN-OH-25 MSRP: Was: Now: $725.00 Add to Cart
206/505 Transmission Gear Shaft Nut Wrench Used to apply torque to the input driven spiral bevel gearshaft duplex bearing outer ring retaining nut. Bell P/N T101502 Helitools' P/N 206-XMSN-OH-03 MSRP: Was: Now: $225.00 Add to Cart
206/505 Mast Holding Fixture Used to hold the mast assembly when torque is applied to the ball bearing retaining nut during removal and installation. Bell P/N 206-240-002-101 Helitools P/N 206-MAST-F-05 CLICK HERE FOR T101499 MSRP: Was: Now: $850.00 Add to Cart
407 Mast Bearing Work Aid P/N 407MBR-HT Used to remove the bearing from the mast assembly. T103318-101 407-MAST-OH-03 MSRP: Was: Now: $550.00 Add to Cart
407 Torque Multiplier Fixture P/N 407TMF-HT Used with your choice of a 4-1 or 3-1 torque multiplier. Let the torque multiplier bump up against the pin to hold backup.This fixture lets you do the mast nut torque or 1-5 hr torque check by yourself not to mention... MSRP: Was: Now: $880.00 Add to Cart
206/505 Trunnion Hex Screw Wrench Used to torque hex insert screw in trunnion/pillow block. 206-MR-OH-18 MSRP: Was: Now: $96.00 Add to Cart
206 & 505 Main Rotor Blade Alignment Pins - 2pcs Easier and faster than mirrors and cheaper than a laser.No calibration needed. Drop it in the bolt hole and set the string. 206-MR-F-06 MSRP: Was: Now: $115.00 - $145.00 Choose Options
407 Tailrotor Gearbox Quill Wrench Used to remove, install or torque the nut from the tail rotor gearbox quills. T101449 407-TRGB-F-05 407-XMSN-F-03 MSRP: Was: Now: $630.00 Add to Cart
Rolls-Royce 250 PTO Seal Remover Used to remove single lip PTO seal on RR250 engines. Thread into the seal and use slide hammer to remove. MSRP: Was: Now: $525.00 Add to Cart
206 Planetary Shaft Sleeve Used to remove aand install the planet gear shaft from and into the arm of the spider and the bearing assembly inner race. T101506 206-XMSN-OH-20 MSRP: Was: Now: $525.00 Add to Cart
206/407/505 Freewheeling Unit Wrench Used to remove and install the 214-040-241 nut. This tool replaces wrench assembly 407-240-006-101. 206-FWU-OH-18 T101960 MSRP: Was: Now: $150.00 Add to Cart
206/505/407 Freewheeling Unit Duplex Bearing Removal Driver Used to remove the 406-040-531 bearing from the 406-040-508 Cap Assembly. 206-FWU-OH-15 T103324-101 MSRP: Was: Now: $250.00 Add to Cart
206/407/505 Freewheeling Unit Bearing Installation Sleeve Used to install the 206-040-206 bearing into the 406-040-516 shaft. 206-FWU-OH-17 T103333 MSRP: Was: Now: $90.00 Add to Cart
222 Tail Rotor Gearbox Holder Fixture to hold Tail Rotor Gearbox. 222-TRGB-OH-01 222-TRGB-OH-1B T103036 MSRP: Was: Now: $230.00 Add to Cart
206/407/505 Freewheeling Unit Shaft Removal Work Aids Used in conjuction with a press to remove the shaft from the bearing. T103310-101 MSRP: Was: Now: $150.00 - $450.00 Choose Options
429 PW207 Mag Seal Puller Slide Hammer used to remove Seal P/N 3058291-01 PWC64888 PWC64888-1 Designed with customer to fit tighter than PWC factory workaid. All 3 lips engage. MSRP: Was: Now: $525.00 Add to Cart
C30/47 #1 Bearing in Compressor Puller C30/47 #1 Bearing in Compressor Puller 23005023 MSRP: Was: Now: $850.00 Add to Cart
Oil Collector Pan - Alignment Pilot Workaid Oil Collector Pan - Alignment Pilot Workaid for top case 206-040-550 Figure 63-19 MSRP: Was: Now: $250.00 Add to Cart
Oil Collector Pan - Alignment Pilot Work aid Oil Collector Pan - Alignment Pilot Work aid for top case 206-040-532 Figure 63-19 MSRP: Was: Now: $250.00 Add to Cart
Oil Collector Pan - Alignment Pilot Work Aid Set Oil Collector Pan - Alignment Pilot Work Aid Set For top case 206-040-550 & 206-040-532 Figure 63-19 MSRP: Was: Now: $450.00 Add to Cart
206/407/505 Tail Rotor Output Shaft Nut Work Aid Used to apply torque to and remove the output shaft inner nut. T101513 206-TRGB-OH-05 MSRP: Was: Now: $250.00 Add to Cart
206/505 Tail Rotor Gearbox Backlash Work Aid Used to hold output shaft so you can check the backlash between the tail rotor gearbox input pinion gear and output bevel gear. T102093 206-TRGB-OH-06 MSRP: Was: Now: $450.00 Add to Cart
407 Mast Assembly Nut Wrench Wrench is used to remove and torque the nut on the mast assembly bearing during overhaul. 407-240-007-101/105 407-240-007-105 407-MAST-02 MSRP: Was: Now: $1,300.00 Add to Cart
205/212/214/412 External Spline Wrench 205/212/214/412 External Spline Wrench 412-XMSN-OH-01 T101306 MSRP: Was: Now: $1,050.00 Add to Cart
206 Tail Rotor Bearing Installation Used in conjuction with a hydralic press to push out the bearing from the side of the blade that has the swaged lip. MSRP: Was: Now: $375.00 Add to Cart
407 Freewheeling Unit Nut Wrench Used to install the freewheel nut 407-FWU-OH-21 407-240-006 MSRP: Was: Now: $1,980.00 Add to Cart
407 Transmission Input Pinion Assembly And Removal Adapter Used in conjunction with a puller to remove and install the transmission pinion assembly Helitools 407-XMSN-OH-02 Bell 407-240-003 MSRP: Was: Now: $300.00 Add to Cart
206B/L/505 Main Rotor Static Balance Kit Static Balancing Kit for 206B/L and 505. Comes in protective case with extra plastic bin to store lead weights. This is from Chuck Dugan from Helitools. We acquired his inventory. Contact us for any other tools that was previously supplied by... MSRP: Was: Now: $4,900.00 Add to Cart
